View MNR15_235622.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

MNR15
Resistors
Chip resistor networks
MNR15 (0603x5 size)
Features 1) Suitable for pull-up and pull-down resistors. 2) No direction to be mounted by placing common electrode with symmetry. 3) Convex electrodes Easy to check the fillet after soldering is finished. 4) High-density mounting Can be mounted even densely than eight 0402chips (MCR01), and mounting costs are lower. 5) Compatible with a wide range of mounting machines. Squared corners make it excellent for mounting using image recognition machines. 6) ROHM resistors have approved ISO-9001 certification. Design and specifications are subject to change without notice. Carefully check the specification sheet supplied with the product before using or ordering it.
Ratings
Item Rated power Conditions Power must be derated according to the power derating curve in Figure 1 when ambient temperature exceeds 70C.
100 80 60 40 20 0
Specifications 0.031W (1 / 32W) at 70C
POWER LOAD (%)
-55
0
70
100
125
AMBIENT TEMPERATURE (C)
Fig.1
Rated voltage
The voltage rating is calculated by the following equation. If the value obtained exceeds the limiting element voltage, the voltage rating is equal to the maximum operating voltage. E : Rated voltage (V) P : Rated power (W) R : Nominal resistance ()
E= PxR
Nominal resistance Operating temperature
Limiting element voltage
12.5V
See Table 1.
-55C to +125C
Table 1
Resistance tolerance
J (5%)
Resistance range ()
56R100k (E24)
Resistance temperature coefficient (ppm / C)
200
Before using components in circuits where they will be exposed to transients such as pulse loads(short-duration, high-level loads), be certain to evaluate the component in the mounted state. In addition, the reliability and performance of this component cannot be guaranteed if it is used with a steady state voltage that is greater than its rated voltage.
Rev.B
1/4
MNR15
Resistors
Characteristics
Item Resistance Variation of resistance with temperature Overload Guaranteed value Resistor type J : 5% See Table.1 (2.0%+0.1) A new uniform coating of minimum of 95% of the surface being immersed and no soldering damage. (1.0%+0.05) No remarkable abnormality on the appearance. (1.0%+0.05) (3.0%+0.1) Damp heat, steady state (3.0%+0.1) Endurance at 70C (3.0%+0.1) Endurance (1.0%+0.05) Resistance to solvent (1.0%+0.05) Without mechanical damage such as breaks. Test conditions (JIS C 5201-1) JIS C 5201-1 4.5 JIS C 5201-1 4.8 Measurement : +25 / +125C JIS C 5201-1 4.13 Rated voltagex2.5, 2s. Maximum Overload Voltage : 25V JIS C 5201-1 4.17 Rosin*Ethanol (25%WT) Soldering condition : 2355C Duration of immersion : 2.00.5s. JIS C 5201-1 4.18 Soldering condition : 2605C Duration of immersion : 101s. JIS C 5201-1 4.19 Test temp. : -55C to +125C 5cyc JIS C 5201-1 4.24 40C, 93%RH Test time : 1,000h to 1,048h JIS C 5201-1 4.25.1 Rated voltage, 70C 1.5h : ON - 0.5h : OFF Test time : 1,000h to 1,048h JIS C 5201-1 4.25.3 125C Test time : 1,000h to 1,048h JIS C 5201-1 4.29 235C, Immersion cleaning, 50.5min. Solvent : 2-propanol JIS C 5201-1 4.33
Solderability
Resistance to soldering heat Rapid change of temperature
Bend strength of the end face plating
External dimensions (Unit : mm)
3.20.1 a
b
b
B
a : 0.480.15 b : 0.320.15
No.
Material
Thick dielectric glaze of oxide metal
0.30.1
A A'
0.350.1
1.60.1
Thick film of silver for electrode Nickel-coated electrode External electrode coated with Sn Alumina substrate

B'
0.64
Overcoating (Resin)
0.50.1
Pitch of the upper electrode.
Cross section A-A'
1
Cross sectionB-B'
1
Maqnification
Rev.B
2/4
MNR15
Resistors
Equivalent circuit
R1 R5 R6
R2 R7
R3 R8
R4
R1 = R2 = R3 = R4 = R5 = R6 = R7 = R8
Packaging
Reel Taping
P0 P2 P1
D0
E F
101 101 101 101
W
B0
08
06
04
02
02
04
06
08
A
B
D
A0
Heat crimp cover / Tape Chip network Thick paper (Underside paper tape) resistors Square punchout hole mount
T2 C
Label EIAJ ET-7200B compliant
(Unit : mm)
W
F
E
A0
B0
(Unit: mm) A B C D
8.00.3
D0
3.50.05
P0
1.750.1
P1
1.80.1
P2
3.40.1
T2
180
0 -1.5
60
+1 0
9
+1.0 0
130.2
1.5 +0.1 0
4.00.1
4.00.1
2.00.05
Max. 1.1
Product designation
MNR1 5
Part No.
E0RP
J 5% J is also used for jumper
J
Nominal resistance
Resistance code,3 digits, 000 denotes Jumper type.
Resistance tolerance
Packaging Specifications Code
Part No. Code Resistance tolerance J(5%) Packaging specifications Reel Basic ordering unit (pcs)
MNR15
E0RP
Paper tape (4mm Pitch)
180mm (7in.)
5,000
Reel (180) : JEITA ET-7200B : Standard product
Rev.B
3/4
MNR15
Resistors
Electrical characteristics
6.0 5.0 4.0
DC RESISTANCE (%)
400
JIS C 5201-1 4.5 SAMPLE SIZE : n=24pcs 20C 65%RH
TEMPERATURE COEFICIENT (ppm/C)
300 200
JIS C 5201-1 4.8 SAMPLE SIZE : n=24pcs 25C / 125C
6.0 5.0 4.0 3.0 2.0
3.0 2.0 1.0 0 -1.0 -2.0 -3.0 -4.0 -5.0 -6.0 56 100 1k 10k 100k
JIS C 5201-1 4.13 SAMPLE SIZE : n=24pcs RATED VOLTAGEx2.5TIMES 2S MAXIMUM OVERLOAD VOLTAGE : 25V
R/R (%)
100 0 -100 -200 -300 -400 56 100 1k 10k 100k
1.0 0 -1.0 -2.0 -3.0 -4.0 -5.0 -6.0 56 100 1k 10k 100k
RESISTANCE ()
RESISTANCE ()
RESISTANCE ()
Fig.2 Resistance
Fig.3 Vatiation resistance with temperature
Fig.4 Overload
3.0 2.0 1.0 JIS C 5201-1 4.18 SAMPLE SIZE : n=24pcs SOLDERING CONDITION : 260C 10S
3.0 2.0 1.0
JIS C 5201-1 4.19 SAMPLE SIZE : n=24pcs -55C / 125C 5cyc
6.0 5.0 4.0 3.0 2.0
JIS C 5201-1 4.24 SAMPLE SIZE : n = 24pcs 40C 93%RH WITH NO LOAD 1000h
R/R (%)
R/R (%)
R/R (%)
56 100 1k 10k 100k
1.0 0 -1.0 -2.0 -3.0 -4.0 -5.0 -6.0
0 -1.0 -2.0 -3.0
0 -1.0 -2.0 -3.0
56
100
1k
10k
100k
56
100
1k
10k
100k
RESISTANCE ()
RESISTANCE ()
RESISTANCE ()
Fig.5 Resistance to soldering heat
Fig.6 Rapid change of temperature
Fig.7 Damp heat, steady state
6.0 5.0 4.0 3.0 2.0
JIS C 5201-1 4.25.1 SAMPLE SIZE : n=24pcs 70C 1,000h OVERLOAD : THE RATED VOLTAGE
6.0 5.0 4.0 3.0 2.0
JIS C 5201-1 4.25.3 SAMPLE SIZE : n=24pcs 125C WITH NO LOAD 1,000h
R/R (%)
R/R (%)
56 100 1k 10k 100k
1.0 0 -1.0 -2.0 -3.0 -4.0 -5.0 -6.0
1.0 0 -1.0 -2.0 -3.0 -4.0 -5.0 -6.0 56 100 1k 10k 100k
RESISTANCE ()
RESISTANCE ()
Fig.8 Endurance at 70C
Fig.9 Endurance
Rev.B
4/4
Appendix
Notes
No technical content pages of this document may be reproduced in any form or transmitted by any means without prior permission of ROHM CO.,LTD. The contents described herein are subject to change without notice. The specifications for the product described in this document are for reference only. Upon actual use, therefore, please request that specifications to be separately delivered. Application circuit diagrams and circuit constants contained herein are shown as examples of standard use and operation. Please pay careful attention to the peripheral conditions when designing circuits and deciding upon circuit constants in the set. Any data, including, but not limited to application circuit diagrams information, described herein are intended only as illustrations of such devices and not as the specifications for such devices. ROHM CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any third party's intellectual property rights or other proprietary rights, and further, assumes no liability of whatsoever nature in the event of any such infringement, or arising from or connected with or related to the use of such devices. Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or otherwise dispose of the same, no express or implied right or license to practice or commercially exploit any intellectual property rights or other proprietary rights owned or controlled by ROHM CO., LTD. is granted to any such buyer. Products listed in this document are no antiradiation design.
The products listed in this document are designed to be used with ordinary electronic equipment or devices (such as audio visual equipment, office-automation equipment, communications devices, electrical appliances and electronic toys). Should you intend to use these products with equipment or devices which require an extremely high level of reliability and the malfunction of with would directly endanger human life (such as medical instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other safety devices), please be sure to consult with our sales representative in advance. About Export Control Order in Japan Products described herein are the objects of controlled goods in Annex 1 (Item 16) of Export Trade Control Order in Japan. In case of export from Japan, please confirm if it applies to "objective" criteria or an "informed" (by MITI clause) on the basis of "catch all controls for Non-Proliferation of Weapons of Mass Destruction.
Appendix1-Rev1.1

▲Up To Search▲

Price & Availability of MNR15

	To Download MNR15 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .